MSO5000 Software Options Bundle for FREE

CONTACT ACCOUNT

TEL: 0118 978 6911

Home / Posted by James (Page 6)

Author Archive

MSO5000 Software Options Bundle for FREE

Posted on: July 20th, 2020 by James

July 20, 2020
FREE Software Options Bundle including; RS232/UART, I2C/SPI, CAN/LIN, FlexRay, I2S, AWG and PWR. RS232/UART - Decoding functions Licence. EMBD I2C/SPI - Embedded Serial Bus Trigger and Analysis. AUTO CAN/LIN - Auto Serial Bus Trigger and Analysis. FlexRay - FlexRay Serial Bus Trigger and Analysis....

DS/MSO2000A Software Options Bundle for FREE!

Posted on: July 20th, 2020 by James

July 20, 2020
FREE Software Options Bundle including Advanced Trigger Functions, Serial-Bus Decoding and CAN-Bus! Advanced Trigger Functions - Advanced trigger functions (Windows, Nth Edge, HDTV, Delay, Time Out, duration & USB). Serial Bus Decoding Functions - RS232, I2C & SPI bus decoding functions. CAN Bus Trigger and Decoding Functio...

DS1000Z / Z-S / Z-E Software Options Bundle for FREE

Posted on: July 17th, 2020 by James

July 17, 2020
FREE Software Options Bundle including Advanced Trigger Functions, Serial-Bus Decoding and CAN-Bus! Advanced Trigger Functions - The Rigol AT-DS1000Z advanced trigger functions licence permanently enables the following trigger functions - RS232, I2C, SPI, Runt, Windows, Nth Edge, Delay, Time Out, Setup/Hold. Deep Memory - The Rigol MEM-DS1000...

What will my unit come with as standard?

Posted on: July 16th, 2020 by James

July 16, 2020
All Rigol units will come with a UK Power Cable, PDI & Safety Test as standard. All other Standard Accessories will be dependant on the products that was purchased....

Can I get help with programming my instrument?

Posted on: July 16th, 2020 by James

July 16, 2020
RIGOL provides drivers and programming functions as part of your warranted and purchased package. Programming itself can be achieved in many different ways with tools which are largely the choice of the customer. For this reason, we can't support your systems but we can sometimes help you find information - we ask you to first review the programming guide for your instrument and make sure it is su...

What file formats does RIGOL use for storage of waveforms etc? What is the different between Trace and Waveform?

Posted on: July 16th, 2020 by James

July 16, 2020
To access, on oscilloscopes for example, press [Storage] to select the desired storage type. The default is “Picture”. The storage and recall descriptions of each type are as follows, with the examples in this case taken from as DS2000-series oscilloscope (so other instruments such as DG-series won't offer everything below): 1. Traces Save the waveform data in external memory in “*.tr...

USB stick / flash drive / memory sticks must fully compliant with USB2.0* standard compliant w/Win7 – Info on good sticks, esp. earlier models:

Posted on: July 16th, 2020 by James

July 16, 2020
We have found many instruments to be fussy about USB sticks (more common on instruments of slightly longer-standing design). Like PictBridge standard, USB memory specs can be quite open to interpretation and may vary between manufacturers. Please try the following guidelines if you are having difficulty - it is especially important you can rely on the stick you have chosen, if you decide to do ...

X-Y Display mode on Scopes – additional features with RIGOL DS1000Z-series oscilloscope (DS1074, DS1074Z-S, DS1104Z, DS1104Z-S)

Posted on: July 16th, 2020 by James

July 16, 2020
New DS1000Z series offers more in X-Y mode: In this mode, the Rigol DS1074Z oscilloscope changes 2 of the 4 channels from voltage-time display mode to voltage-voltage display mode. The phase deviation between two signals with the same frequency can be easily measured via Lissajous method. The figure below shows the measurement schematic diagram of the phase deviation. To access the Lissajou ...

Getting started with Rigol PC Software Tools

Posted on: July 16th, 2020 by James

July 16, 2020
Rigol software files are downloaded in .rar data containers or .zip compressed files. The files must be unpacked or unzipped before installation. Ultra Sigma must be installed before any other Rigol application, except Ultra Wave. To open a Rigol software application after installation (excluding S1210, S1220, S1501 and Ultra Wave)... Open Ultra Sigma > Conn...

How do I connect my instrument via my LAN to UltraSigma PC Software?

Posted on: July 16th, 2020 by James

July 16, 2020
First of all, ensure your instrument as the option for LAN connection and ensure you have a PC running the latest version of UltraSigma download from RIGOL and this PC is successfully connected to the same local area network as you're plugging your instrument into. In order for you to connect your Rigol equipment via LAN you must: Ensure your instrument is connected through the LAN...

Sub Categories

Additional Support (1)

Blog (36)

Buyer's Guide (3)

Customer FAQ/Help (31)

Electronic Load Offers and Promotions (1)

Electronic Load Support (3)

EMC Support (3)

General Product Support (3)

International Shipping (4)

Multimeters Support (3)

New Products (4)

Order Status (7)

Oscilloscope Offers & Promotions (6)

Oscilloscope Support (5)

Power Supply Offers & Promotions (1)

Power Supply Support (3)

Pricing and Billing (5)

Product Support (13)

RF Signal Generator Support (3)

Rigol Offers and Promotions (6)

Spectrum Analyser Offers & Promotions (3)

Spectrum Analyser Support (5)

Waveform Generator Support (3)