Knowledge Base:  
Knowledge Base > Spectrum Analysers --> Knowledge Base > Spectrum Analysers
How to get the specified DANL of -135dBm? (typ, +6dB f/GHz)
Last Updated: 01/08/2014
A simple sequence of settings will help you dig into the noise floor. With any Spectrum Analyser, setting up the (1) Span, (2) Attenuator, (3) Pre-amp and (4) Resolution Bandwidth settings - these are all important starting points to getting the best noise floor. Remember, safety first (no input or power RF nearby) and try adjusting these four settings to find out more about what to turn on, and off, to get the best from DSA815. (Like most other spectrum analysers, other settings e.g. Filter and Detector types can also affect your exact noise floor and can do so in non-linear or non-additive ways)
Remember, you don't always want, or NEED the lowest noise floor possible for your tests because you may compromise on breadth of SPAN or you may find yourself waiting for long SWEEP TIMES so take care to decide what is best for your test-methods.
As just ONE example of the many different ways of working with spectrum analysers, if you are working with EMC Pre-Compliance, it will usually be impractical to work at noise floors this low (for most of the time anyway!) because you may be hunting for noise changes over a wide range of frequencies or spans - at least initially....
BUT you do want them sufficiently low to see how your changes are improving your emissions!
Always consult your EMC expert about the noise floor required to get reliable test results in your test environment and for your EUT. In EMC work, for example when estimating the improvements you have made to your Golden Product (the unit unchanged from your first EMC lab visit), always try to work with a noise floor low enough that you can ignore it altogether.
THE GOLDEN RULE:
Using your Golden Product, make only like-with-like tests to judge your improvement in emissions - i.e. do both these sweeps on as identical test set-ups as you can:
(i) sweep your Golden Product with DSA815 (with negligible noise floor), then
(ii) sweep your IMPROVED product (with same negligible noise floor) and compare the emissions levels of both.
Keep switching between with different settings to cover your range of concern as necessary - if your noise floors are negligible, you may be closing in on expected improvements from your next precious EMC Lab visit!
The Golden Product approach, together with some wise EMC-experienced eyes, can be powerful -
...that way, you are effectively eliminating the ever-fickle noise floor from your sums.
THE ABOVE IS NOT TO BE USED AS ADVICE FOR YOUR PARTICULAR EMC TEST REQUIREMENT - GENERAL PRODUCT INFORMATION IS ALWAYS BEST SUPPLEMENTED WITH A PROVEN, WELL-DESIGNED METHODOLOGY FROM AN EXPERIENCED EMC PRACTITIONER.

Was this article helpful?

Comments:
 

Related Articles
 > Is there an attenuator built-in on RIGOL's DSA815?
 > Is there an attenuator built-in on RIGOL's DSA1030?
 > Are there any independent reviews of RIGOL Spectrum Analysers like DSA815 in the UK?
 > How do I add a horizontal Display Line to my DSA screen?
 > How to reduce or lower noise floor? (DSA815 and DSA1030)
 > How do I check my DSA is working properly?
 > How do radio amateurs use RIGOL's DSA815? And for what kinds of applications?
 > I just received mine… how can I tell if it's working OK?
 > Can I get help on using complex functions of my instrument?
 > Can I get help with programming my instrument?
 > Will I get a UK phone number for the team who sold to me?
 > How do I achieve the lowest DANL with my spectrum analyser?
 > How to measure an RF Amplifier using a DSA-800 Series Spectrum Analyzer
 > EMC Precompliance: Testing on a budget
 > How do I measure an RF Bandpass filter
 > How do I connect my instrument via my LAN to UltraSigma PC Software?
 > After receiving my instrument(s), what should I do with my RIGOL Warranty Card?
 > Can I get Rigol firmware updates?
 > When installing Ultra Sigma I get a message PC telling me to install NIVISA / VISA Runtime engine. What am i doing wrong?
 > What about RIGOL battery and portable use? Can you run RIGOL Scopes and Spectrum Analysers from Battery or portable UPS Power Supplies?
 > USB stick / flash drive / memory sticks must fully compliant with USB2.0* standard compliant w/Win7 - Info on good sticks, esp. earlier models:
 > RIGOL 3GHz Spectrum Analyser - Applications insights from RIGOL-UK's customers.
 > Getting started with Rigol PC Software Tools
 > AMK: What do you get with the DSA Advanced Measurement Kit ? (DSA1000-AMK)
 > test
 > How do i measure an RF Attenuator?
 > Using a Rigol product key to generate a Rigol software licence code.
 > Rigol PC Software Summary
 > Rigol PC Software Versions
 > Can I get IVI drivers for my Rigol test equipment?