 |
 |
 |
|
The Rigol DG900 series offers a user-friendly and high-performance function/arbitrary waveform generator solution at a very attractive price. Each instrument provides many functions including; function generator, arbitrary waveform generator, noise source, pulse generator, harmonics generator, analogue / digital modulator and frequency counter. Any Rigol DG900 series function/arbitrary waveform generator would be a valuable asset in any home, business or education laboratory.
For further information, please refer to the 'SPECIFICATION' and 'DOCUMENTS, SOFTWARE & VIDEOS' tabs, above.
An overview of all Rigol function / arbitrary waveform generators can be found HERE.
Click image to enlarge
|
Model
|
DG952
|
DG972
|
DG992
|
|
Channels
|
2
|
|
Maximum Frequency
|
50MHz
|
70MHz
|
100MHz
|
|
Sample Rate
|
250MSa/s
|
|
Waveforms
|
|
Basic Waveforms
|
Sine, square, ramp, pulse, noise, DC, dual-tone
|
|
Advanced Waveforms
|
PRBS, RS232, sequence
|
|
Built-In Arbitrary Waveforms
|
160-off, including: Sinc, exponential rise, exponential fall, ECG,
Gauss, HaverSine, Lorentz, etc
|
|
Frequency Characteristics
|
|
Sine
|
1μHz to 50MHz
|
1μHz to 70MHz
|
1μHz to 100MHz
|
|
Square
|
1μHz to 15MHz
|
1μHz to 20MHz
|
1μHz to 25MHz
|
|
Ramp
|
1μHz to 1.5MHz
|
1μHz to 1.5MHz
|
1μHz to 2MHz
|
|
Pulse
|
1μHz to 15MHz
|
1μHz to 20MHz
|
1μHz to 25MHz
|
|
Harmonic
|
1μHz to 20MHz
|
1μHz to 20MHz
|
1μHz to 25MHz
|
|
PRBS
|
2kbps to 40Mbps
|
2kbps to 50Mbps
|
2kbps to 60Mbps
|
|
Dual-tone
|
1μHz to 20MHz
|
1μHz to 20MHz
|
1μHz to 20MHz
|
|
RS232
|
baud rate range: 9600, 14400, 19200, 38400, 57600, 115200, 128000, 230400
|
|
Sequence
|
2kSa/s to 60MSa/s
|
|
Noise (-3dB)
|
100MHz bandwidth
|
|
Arbitrary Waveform
|
1μHz to 15MHz
|
1μHz to 20MHz
|
1μHz to 20MHz
|
|
Resolution
|
1μHz
|
|
Accuracy
|
±(1ppm of the set value + 10pHz), 18⁰C to 28⁰C
|
|
Sine Wave Spectral Purity
|
|
Harmonic Distortion
|
<-55dBc typical (DC to 10MHz @ 0dBm)
<-50dBc typical (10MHz to 20MHz @ 0dBm)
<-40dBc typical (20MHz to 40MHz @ 0dBm)
<-35dBc typical (>40MHz @ 0dBm)
|
|
Total Harmonic Distortion
|
<0.075% (10Hz to 20kHz @ 0dBm)
|
|
Spurious (Non-Harmonic)
|
<-60dBc (f ≤ 10MHz)
<-60dBc + 6dB/octave (f > 10MHz)
|
|
Phase Noise
|
<-105dBc/Hz @ 10kHz offset (f = 10MHz @ 0dBm)
|
|
Signal Characteristics
|
|
Square Wave
|
Rise / Fall Time
|
≤9ns typical (1Vpp, 1kHz)
|
|
Overshoot
|
≤5% typical (1Vpp, 100kHz)
|
|
Duty Cycle
|
0.01% to 99.99% (Limited by the current frequency setting)
|
|
Non-Symmetry
|
1% of the period + 4ns
|
|
Jitter (rms)
|
2ppm of the period + 200ps typical (f ≤ 5MHz, 1Vpp)
200ps (f > 5MHz, 1Vpp)
|
|
Ramp
|
Linearity
|
≤1% of peak output, typical (1Vpp, 1kHz, 100% symmetry)
|
|
Symmetry
|
0% to 100%
|
|
Pulse
|
Pulse Width
|
16ns to 1000ks (Limited by the current frequency setting)
|
|
Duty
|
0.001% to 99.999% (Limited by the current frequency setting and the pulse width setting)
|
|
Rising / Falling Edge
|
≥8ns (Limited by the current frequency setting and the pulse width setting)
|
|
Overshoot
|
≤5% typical (1Vpp, 1kHz)
|
|
Jitter (rms)
|
2ppm of the period + 200ps typical (f ≤ 5MHz, 1Vpp)
200ps (f > 5MHz, 1Vpp)
|
|
Arbitrary Waveform
|
Maximum Length
|
16Mpts
|
|
Vertical Resolution
|
16 bits
|
|
Sample Rate
|
10Sa/s to 60MSa/s (Interpolation filter)
2kSa/s to 50MSa/s (Step filter)
2kSa/s to 50MSa/s (Smooth filter)
|
|
Min. Rise / Fall Time
|
≥8ns (Interpolation filter)
3.0/sample rate (Step filter)
1.0/sample rate (Smooth filter)
|
|
Jitter (rms)
|
≥200ps typical (Interpolation filter, 1Vpp)
<5ps typical (Step filter, 1Vpp)
<5ps typical (Smooth filter, 1Vpp)
|
|
Overshoot
|
≤5% typical (1Vpp)
|
|
Harmonic Generator
|
Harmonic Order
|
≤8
|
|
Harmonic Type
|
Even Harmonic, Odd Harmonic, Order Harmonic, User
|
|
Harmonic Amplitude
|
The amplitude of each harmonic can be set independently
|
|
Harmonic Phase
|
The phase of each harmonic can be set independently
|
|
Output Characteristics
|
|
Amplitude (into 50Ω)
|
Range
|
1.0mVpp to 10Vpp (f ≤ 10MHz)
1.0mVpp to 5.0Vpp (f ≤ 30MHz)
1.0mVpp to 2.5Vpp (f ≤ 60MHz)
1.0mVpp to 1.0Vpp (f > 60MHz)
|
|
Accuracy
|
±1% of the set value ±5mV, typical (1kHz sine, 0V offset, >10mVpp, auto)
|
|
Flatness
|
±0.1dB typical (f ≤ 5MHz)
±0.2dB typical (f ≤ 15MHz)
±0.3dB typical (f ≤ 25MHz)
±0.5dB typical (f ≤ 40MHz)
±1dB typical (f > 40MHz)
|
|
Units
|
Vpp, Vrms, dBm
|
|
Resolution
|
0.1mVpp or 4 digits
|
|
Offset (into 50Ω)
|
Range
|
±5Vpk AC + DC
|
|
Accuracy
|
±(1% of the setting value + 5 mV + 1% of the amplitude)
|
|
Output
|
Impedance
|
50 Ω typical
|
|
Protection
|
Short-circuit protection - The output is disabled automatically when an overload occurs
|
|
Modulation Characteristics
|
|
Types
|
AM, FM, PM, ASK, FSK, PSK, PWM
|
|
AM
|
Carrier Waveform
|
Sine, Square, Ramp, Arb
|
|
Source
|
Internal / External
|
|
Modulating Waveform
|
Sine, Square, Ramp, Noise, Arb
|
|
Modulation Depth
|
0% to 120%
|
|
Modulation Frequency
|
2mHz to 1MHz
|
|
FM
|
Carrier Waveform
|
Sine, Square, Ramp, Arb
|
|
Source
|
Internal / External
|
|
Modulating Waveform
|
Sine, Square, Ramp, Noise, Arb
|
|
Modulation Frequency
|
2mHz to 1MHz
|
|
PM
|
Carrier Waveform
|
Sine, Square, Ramp, Arb
|
|
Source
|
Internal / External
|
|
Modulating Waveform
|
Sine, Square, Ramp, Noise, Arb
|
|
Modulation Deviation
|
0° to 360°
|
|
Modulation Frequency
|
2mHz to 1MHz
|
|
ASK
|
Carrier Waveform
|
Sine, Square, Ramp, Arb
|
|
Source
|
Internal / External
|
|
Modulating Waveform
|
Square with 50% duty cycle
|
|
Modulation Frequency
|
2mHz to 1MHz
|
|
FSK
|
Carrier Waveform
|
Sine, Square, Ramp, Arb
|
|
Source
|
Internal / External
|
|
Modulating Waveform
|
Square with 50% duty cycle
|
|
Modulation Frequency
|
2mHz to 1MHz
|
|
PSK
|
Carrier Waveform
|
Sine, Square, Ramp, Arb
|
|
Source
|
Internal / External
|
|
Modulating Waveform
|
Square with 50% duty cycle
|
|
Modulation Frequency
|
2mHz to 1MHz
|
|
PWM
|
Carrier Waveform
|
Pulse
|
|
Source
|
Internal / External
|
|
Modulating Waveform
|
Sine, Square, Ramp, Noise, Arb
|
|
Width Deviation
|
0% to 100% of the pulse width
|
|
Modulation Frequency
|
2mHz to 1MHz
|
|
External Modulation Input
|
Input Range
|
75mVrms to ±5Vac+dc (AM, FM, PM)
5V TTL (ASK, FSK, PSK)
|
|
Input Bandwidth
|
50kHz
|
|
Input Impedance
|
10kΩ
|
|
Burst Characteristics
|
|
Carrier Waveform
|
Sine, Square, Ramp, Pulse, Noise, Arb, PRBS, RS232, Sequence (except DC, dual-tone and Harmonic)
|
|
Carrier Frequency
|
2mHz to 50MHz
|
2mHz to 70MHz
|
2mHz to 100MHz
|
|
Burst Count
|
1 to 1,000,000 or Infinite
|
|
Internal Period
|
1μs to 500s
|
|
Gated Source
|
External Trigger
|
|
Source
|
Internal, External, Manual
|
|
Trigger Delay
|
0ns to 100s
|
|
Sweep Characteristics
|
|
Carrier Waveform
|
Sine, Square, Ramp, Arb
|
|
Type
|
Linear, Log, and Step
|
|
Orientation
|
Up / Down
|
|
Start / Stop Frequency
|
Same as the upper / lower limit of the corresponding carrier frequency
|
|
Sweep Time
|
1ms to 500s
|
|
Hold / Return Time
|
0ms to 500s
|
|
Source
|
Internal, External, Manual
|
|
Marker
|
Falling edge of the sync signal (programmable)
|
|
Frequency Counter
|
|
Measurement Function
|
Frequency, Period, Positive/Negative Pulse Width, Duty Cycle
|
|
Frequency Resolution
|
7 digits/s (Gate Time = 1s)
|
|
Frequency Range
|
1μHz to 240MHz
|
|
Voltage Range and Sensitivity (non-modulating signal)
|
DC Coupling
|
±1.5 Vdc DC offset range
50mVrms to ±2.5Vac+dc, 1μHz to 100MHz
100mVrms to ±2.5Vac+dc, 100MHz to 240MHz
|
|
AC Coupling
|
50mVrms to ±2.5Vpp, 1μHz to 100MHz
100mVrms to ±2.5Vpp, 100MHz to 240MHz
|
|
Pulse Width and Duty Cycle Measurement
|
Frequency Range
|
1μHz to 25MHz
|
|
Amplitude Range
|
50mVrms to ±2.5Vac+dc
|
|
Pulse Width
|
20ns minimum
5ns resolution
|
|
Duty Measurement Range
|
0% to 100%
|
|
Input Characteristics
|
Input Impedance
|
1MΩ
|
|
Coupling Mode
|
AC & DC
|
|
Breakdown Voltage
|
±7Vac+dc
|
|
High Frequency Rejection
|
On: Input Bandwidth = 150kHz
Off: Input Bandwidth = 240MHz
|
|
Trigger Level Range
|
-2.5V to +2.5V
|
|
Trigger Sensitivity Range
|
High, Low
|
|
Trigger Characteristics
|
|
Trigger Input
|
Level
|
TTL-compatible
|
|
Slope
|
Rising or falling (selectable)
|
|
Pulse Width
|
>100ns
|
|
Latency
|
<100ns typical (sweep)
<350ns typical (burst)
|
|
Trigger Output
|
Level
|
TTL-compatible
|
|
Pulse Width
|
>60ns typical
|
|
Maximum Frequency
|
1MHz
|
|
Two-channel Characteristics - Phase Offset
|
|
Range
|
0° to 360°
|
|
Waveform Phase Resolution
|
0.03°
|
|
Reference Clock
|
|
External Reference Input
|
Lock Range
|
10MHz ± 50Hz
|
|
Level
|
250mVpp to 5Vpp
|
|
Lock Time
|
<2s
|
|
Input Impedance
|
1kΩ typical (AC coupling)
|
|
Internal Reference Output
|
Frequency
|
10MHz ± 50Hz
|
|
Level
|
3.3Vpp
|
|
Output Impedance
|
50Ω typical, (AC coupling)
|
|
Synchronous Output
|
|
Level
|
TTL-compatible
|
|
Impedance
|
50Ω nominal
|
|
Protection
|
|
Over-Voltage
|
Occurs when:
The instrument amplitude setting is greater than 3.2Vpp or the output AC+DC is greater than |1.6Vdc| and the input voltage is greater than ±12
× (1 ± 5%)V (<10kHz). Disruptive discharge voltage: ±5Vac+dc.
The instrument amplitude setting is smaller than or equal to 3.2Vpp or the output AC+DC is smaller than |1.6VDC| and the input voltage is
greater than ±2.6 × (1 ± 5%)V (<10kHz). Disruptive discharge voltage: ±18Vac+dc.
|
|
Over-Current
|
Occurs when:
The current is greater than ±240mA.
|
|
Programming Time
|
|
Configuration Changes
|
USB
|
|
Function Change
|
10ms
|
|
Amplitude Change
|
5ms
|
|
Frequency Change
|
5ms
|
|
General Specifications
|
|
Communications Interfaces
|
USB Host & USB Device (standard)
USB-LAN (optional)
|
|
Power Supply
|
Voltage
|
100V to 127V (45Hz to 440Hz)
100V to 240V (45Hz to 65Hz)
|
|
Power Consumption
|
<30W
|
|
Display
|
Type
|
4.3" TFT LCD touch-screen
|
|
Resolution
|
480 × 272
|
|
Colour
|
16M
|
|
Environmental
|
Temperature Range
|
0℃ to 45℃ (operating)
-40℃ to 60℃ (storage)
|
|
Cooling Method
|
Convection
|
|
Humidity Range
|
≤95%RH (below 30℃)
≤75%RH (30℃ to 40℃)
≤45%RH (40℃ to 50℃)
|
|
Altitude
|
<3,000m (operating)
<15,000m (non-operating)
|
|
Mechanical
|
Dimensions (W × H × D)
|
238 × 97 × 266.6mm
|
|
Weight
|
1.75kg (excluding the package)
2.85kg (including the package)
|
|
IP Protection
|
IP2X
|
|
Recommended Calibration Interval
|
1 year
|
|
EMC
|
Compliant with EN61326-1:2006
|
|
IEC 61000-3-2:2000
|
±4.0kV (contact discharge)
±4.0kV (air discharge)
|
|
IEC 61000-4-3:2002
|
3V/m (80MHz to 1GHz)
3V/m (1.4GHz to 2GHz)
1V/m (2.0GHz to 2.7GHz)
|
|
IEC 61000-4-4:2004
|
1kV power line
|
|
IEC 61000-4-5:2001
|
0.5kV (phase-to-neutral voltage)
0.5kV (phase-to-earth voltage)
1kV (neutral-to-earth voltage)
|
|
IEC 61000-4-6:2003
|
3V, 0.15MHz to 80MHz
|
|
IEC 61000-4-11:2004
|
Voltage dip: 0% UT during half-cycle, 0% UT during 1 cycle, 70% UT during 25 cycles
Short interruption: 0% UT during 1 cycle
|
|
Electrical Safety
|
Complies with...
EN 61010-1-2012
USA: UL 61010-1:2012,
Canada: CAN/CSA-C22.2
|
|
|
|
 |
|
 |
|
|
|
 |
|
 |
|
Features
- Unique SiFiII (Signal Fidelity II) technology
- Two fully functional and independent channels
- Maximum frequency 50MHz
- 250MSa/s sample rate
- 16-bit vertical resolution
- Basic waveforms: Sine, square, ramp, pulse, noise, DC, dual-tone
- Advanced waveforms: PRBS, RS232, sequence
- 160-off built-in arbitrary waveforms
- 16Mpts arbitrary waveform memory depth per channel
- Supported modulation: AM, FM, PM, ASK, FSK, PSK & PWM
- Intuitive arbitrary waveform editing software for PC
- ±1ppm frequency stability
- Phase noise <-105dBc/Hz @ 10kHz (f = 10MHz)
- Built-in 7 digit counter up to 240MHz
- Built-in 8th order harmonics generator
- Waveform summing function
- 4.3" TFT LCD colour touch-screen display (480 x 272), 16M colours
- Connectivity... USB Host & Device, (USB-LAN optional)
- Standard accessories... UK & European mains leads, BNC cable, USB cable, quick guide
- Optional accessories... 40dB attenuator, USB to LAN module
- Other options include... Standard calibration (traceable to UK national standards), UKAS calibration
|
|
|
|
|
|
|
(
